pascallanger/DIY-Multiprotocol-TX-Module

📋 Change Log since v1.3.4.0

• [DSM/DSM2SFC](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-dsm2sfc---6)
• New DSM2 surface protocol
• [Kyosho3/ASF](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#kyosho3---98)
• New Kyosho ASF surface protocol
• [TRAXXAS/TQ2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#traxxas---43)
• 4 to 6 channels -> Warning: channels order changed
• [TRAXXAS/TQ1](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#traxxas---43)
• New TQ1 surface protocol
• + 39 more

📋 Change Log since v1.3.3.33

• [Automatic builds](https://downloads.multi-module.org/)
• Separated Air and Surface (SFC) protocols into different builds to gain flash space
• Added EU/FCC builds
• [E129/C186](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-c186---1)
• New circular flight and flip flags
• [V911S/E119](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-e119---1)
• New 6G/Senior and light flags
• [Kyosho/FHSS](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-fhss---0)
• + 27 more

📋 Change Log since v1.3.3.20

• [V761/4CH](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-4ch---1)
• Telemetry for the newest models (761-11 and above): the battery status ok/empty is in A1 (4.4V -> 2.2V)
• [FX/9630](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-9630---2)
• New protocol for the FX9630 and QIDI-550 models
• [DSM_RX](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#dsm_rx---70)
• Thanks @johnnym007
• DSM TX clone capabilities. Added sub protocols Clone and Erase. Need the latest (nightly?) version of EdgeTX to access the Clone option.
• [FrSkyX2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#frskyx2---64)
• + 12 more

📋 Change Log since v1.3.3.14

• [V761/TOPRC](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-toprc---2)
• New protocol for the Top RC Hobby Spitfire, P51D, BF-109
• [FX/620](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-620---1)
• New protocol for the FX620 SU35
• [MT99XX2/PA18](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#mt99xx2---92)
• New protocol for the PA18 mini - UNTESTED and only 1 ID
• [Kyosho2/KT-17](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#kyosho2---93)
• New protocol - UNTESTED and only 1 ID
• + 4 more

📋 Change Log since v1.3.3.7

• [E129/C186](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#e129---83)
• New protocol for the C186/E120, C127/E110, K127 helis
• [MT99XX2/PA18](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#mt99xx2---92)
• New protocol for the PA18 mini - UNTESTED and only 1 ID
• [HoTT](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#hott---57)
• Fix failsafe for all 16 channels
• [HoTT Model Locator script](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/tree/master/Lua_scripts)
• New script
• + 7 more

📋 Change Log since v1.3.3.0

• [V911S/E119](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-e119---1)
• Added 6G/3D channel for planes like the XK A220 P-40, newer XK A800
• [MT99xx/A180](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-a180---5)
• Added 6G/3D channel and RX LED channel for planes like the F949S
• [HoTT](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#HoTT---57)
• Added HoTT device warnings. Need the latest OpenTX version.
• [MT99xx/DRAGON](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-dragon---6)
• Compatible with the Eachine Mini Cessna
• + 10 more

📋 Change Log since v1.3.2.86

• [Xerall](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#xerall---91)
• New protocol for the Xerall TankCopter
• [KF606/MIG320](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#KF606---49)
• New sub protocol for the Zhiyang MIG-320 plane
• [MT99xx/F949G](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#mt99xx---17)
• New sub protocol for the F949G plane
• [V911S](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#V911S---46)
• Added Rate on channel 6 (default is high)
• + 22 more

📋 Change Log since v1.3.2.77

• [LOSI](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#losi---89)
• New protocol emulating the LSR-3000 TX
• Only 1 ID available. More IDs can be added if you dump your original TX
• [Mould King](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#mouldkg---90)
• Technic Brick models
• Analog and digital TXs
• Up to 4 bricks=16 motors can be controlled at the same time
• [XK](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#XK---62)
• + 6 more

📋 Change Log since v1.3.2.61

• [DSM/DSMR](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-dsmr_1f---5)
• New DSMR subprotocol for DSMR surface receivers
• Only 22 IDs available, use RX num to cycle through them
• Telemetry enabled
• [Pelikan/SCX24](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-scx24---2)
• New SCX24 subprotocol for 3 channels surface receivers
• TX: Axial AX-4 2.4GHz transmitter and Panda Hobby 3CH Smart Radio 2.4GHz (MT-305A) and Models: Axial SCX24: Deadbolt, Jeep Wranger Rubicon, Chevrolet 1967 C10, B-17 Betty and Panda Hobby: Tetra K1, X1, X2
• [OMP](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#OMP---77)
• + 28 more

📋 Change Log since v1.3.2.58

• Multi core
• Fixed a bug preventing the module to boot when there was an existing signal on the telemetry pin (ie the internal module sending telemetry on the shared telemetry pin on FrSky radios).
• [HoTT](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#hott---57)
• Fixed the Text menu when using Sync mode.

📋 Change Log since v1.3.2.30

• Multi core
• Loads of code optimization with a total of 5KB saved!
• All protocols have been touched in a way or another. Lot of tests have been done but if something is broken please report.
• Protocols using the XN297 emulation @250Kbps use the CC2500 if the RF component is installed (no more switch from NRF to CC2500 based on the RF frequency tune value), if no CC2500 is installed then the NRF24L01 will be used.
• More protocols are available on the CC2500 only modules: GD00X, KF606, OMP (no telemetry), Q90C, SLT, V911S...
• MULTI_STATUS is gone: erskyTX and er9x must be upgraded to the latest test versions.
• Trainer through RX protocols
• By default Multi uses the telemetry line to send the received channels using a RX protocol (FrSky, DSM, AFHDS2A, Bayang) to the radio. But this does not work on FrSky radios since the telemetry lines of the internal and external modules are shared (hardware limitation). On a STM32 module and with a simple hardware modification, you can go around this limitation using CPPM to send the trainer information to the radio.
• + 19 more

📋 Change Log since v1.3.2.12

• [M-Link](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#mlink---78)
• New protocol supporting 16 channels
• Extended limits supported
• Failsafe supported but read the doc!!
• Telemetry: some sort of support from the 2 RXs I have
• Excluded from the T18 5in1 build due to limited Flash space
• [MT99xx](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#mt99xx---17)
• Added the sub protocol A180 for the XK A180 plane
• + 10 more

📋 Change Log since v1.3.2.11

• [OMP](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#omp---77)
• Fixed the protocol which got broken in v1.3.2.11...
• Some code cleaning.

📋 Change Log since v1.3.2.6

• [E016Hv2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#e016hv2---80)
• Removed some left over development codes which were causing issues...
• Protocol now available in the CC2500 only build.
• [E010r5](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#e010r5---81)
• 3 IDs are now available. More IDs can be added if you send me your "unused" original TX.
• [ESKY150v2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#esky150v2---69)
• Protocol now available in the CC2500 only build.
• [AFHDS2A RX](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#flysky-afhds2a-rx---56)
• + 5 more

📋 Change Log since v1.3.1.92

• [HoTT](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#hott---57)
• Fixed a bug in EEPROM handling.
• All RXs will have to be rebound.
• [FlySky AFHDS2A](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#flysky-afhds2a---28)
• Fixed a bug in EEPROM handling.
• RXs with a receiver number above 17 (18..63) will have to be rebound.
• New protocol [LOLI](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#loli---82)
• Receivers: [LOLI3 RX](https://github.com/wooddoor/Loli3)
• + 18 more

📋 Change Log since v1.3.1.78

• New protocol [WFLY2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#wfly2---79)
• Receivers: RF201S,RF206S,RF207S,RF209S
• Extended limits and telemetry supported
• Failsafe currently only set channel values (not hold neither no pulse)
• Option is used to switch between 0=WBUS and 1=PPM
• New protocol [E016Hv2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#e016hv2---80)
• Unknown component emulated with the CC2500
• Make sure to tune the frequency, bind usually requires +40 to complete.
• + 6 more

📋 Change Log since v1.3.1.77

• [XK](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#XK---62) protocol
• Fixed X450 motors twitching from [Issue 347](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/issues/347)
• Build
• New board and code to support the STM32F103C8 64KB controller.
• There is no automatic build since you need to select the protocols you want to fit the smaller flash. Build from Arduino with the latest boards installed.
• Fixed compilation errors when telemetry was disabled.
• [OpenTX Multi Lua scripts](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/tree/master/Lua_scripts)
• DSM FwdPrg.lua updated with more strings

📋 Change Log since v1.3.1.69

• [Kyosho](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#kyosho---73)
• New sub protocol Hype: Transmitters ST6DF, HK6S, Flightsport and receivers ST6DF, HK6DF
• [JJRC345](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#jjrc345---71)
• New sub protocol SkyTmblr: DF-Models SkyTumbler
• [Futaba/SFHSS](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#futaba---21)
• Protocol name changed from SFHSS to Futaba/SFHSS to avoid confusion
• The new name Futaba/SFHSS will appear correclty when using OpenTX 2.3.11 N364+. Otherwise it will appear as SFHSS/SFHSS but still listed under F in alphabetic order
• [OMP](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#OMP---77)
• + 8 more

📋 Change Log since v1.3.1.65

• [OMP](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#OMP---77)
• Corrected a bug in the telemetry (CRC was not activated):
• A1 = battery voltage including "recovered" battery voltage from corrupted telemetry packets
• A2 = battery voltage from only good packets
• You must adjust the battery voltage offset with a voltmeter since there are some large differences between the models
• RX_RSSI = TQly = percentage of received telemetry packets (good and corrupted) received from the model which has nothing to do with how well the RX is receiving the TX
• Telemetry is using the NRF24L01 RF component @250K so depending on your module it might not work so well
• Doc updated
• + 4 more

📋 Change Log since v1.3.1.59

• [OMP](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#OMP---77)
• Added telemetry for A1=battery voltage and TQly=Telemetry quality
• [AFHDS2A](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#FLYSKY-AFHDS2A---28)
• Add 16 channels option to SBUS
• [DSM Forward Programming](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Lua_scripts/README.md#dsm-forward-programming)
• New Lua script to support some basic functions of forward programming. This is a WIP. Please test and report.
• Need the latest OpenTX 2.3.10 nightly and latest Multi version to work on color screens only!
• Multi core
• + 5 more

📋 Change Log since v1.3.1.49

• [OMP](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#OMP---77)
• New protocol for the OMPHOBBY M2 heli
• [Realacc](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#realacc---76)
• New protocol, sub protocol R11
• Untested... The requestor never came back to tell me if the protocol is working...
• [FrSkyR9](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#FRSKYR9---65)
• Improved telemetry
• RX protocols
• + 14 more

📋 Change Log since v1.3.1.36

• [FrSky R9](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#frskyr9---65)
• FCC sub protocol added
• [V2X2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#V2X2---5)
• Fixed issue from last update...
• [Kyosho](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#Kyosho---73)
• New protocol
• Surface protocol called FHSS introduced in 2017. Transmitters: KT-531P, KT-431PT, Flysky Noble NB4 (fw>2.0.67)...
• [Flysky AFHDS2A](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#flysky-afhds2a---28)
• + 16 more

📋 Change Log since v1.3.1.24

• [FrSky R9 Flex 868/915](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#frskyr9---65)
• fixed 868 bind and control
• added additional ID byte: all RXs must be rebound
• added bind options: CH1-8/CH9-16 and Telem ON/OFF. Need OpenTX 2.3.10 not released yet.
• added full telemetry RX to TX (tested)
• added telemetry TX to RX (untested)
• TQly is now the percentage of number of packets received 100%=perfect..0%=signal lost
• [FrSkyX / X2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#frskyx---15)
• + 10 more

📋 Change Log since v1.3.1.9

• T18 5-in-1 initial support
• [FrSky R9 Flex 868/915](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#frskyr9---65)
• [DSM](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#dsm---6)
• servo refresh rate is by default 22ms and can't be changed until the OpenTX code is modified to give the option to switch to 11ms. The current display on OpenTX of DSM 2/X 11/22ms is the frame rate which is not the servo refresh rate.
• SAFE channel association documentation
• [DSM RX](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#DSM_RX---70)
• changed Aileron and Rudder direction to match original radio convention
• bind can be ended on GUI
• + 16 more

📋 Change Log since v1.3.1.1

• New sub protocol for Pelikan: [Lite](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#pelikan---60)
• New sub protocol for Bayang: [QX100](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#sub_protocol-qx100---5)
• New protocol [Q90C](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#q90c---72): this protocol has limited features. If you have a TX then contact me on GitHub or RCGroups.
• Protocol [DSM RX](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#DSM_RX---70): changed Aileron and Rudder direction to match original radio convention.
• Protocol HoTT:
• LBT implemented.
• Full telemetry support including auto sensors discovery.
• Full sensors text config.
• + 5 more

📋 Change Log since v1.3.0.95

• New protocol [DSM RX](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#DSM_RX---70): To be used as a source for Multi/trainer available in OpenTX. Auto detect DSM2/X 11/22ms and 1024/2048 formats at bind time
• New protocol [JJRC345](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#JJRC345---71)
• HoTT: Full telemetry support including auto sensors discovery. Full sensors text config. It should be available in OpenTX 2.3.8N226
• Devo: add basic telemetry TX RSSI, A1 and A2
• [Firmware updates manual](https://www.multi-module.org/using-the-module/firmware-updates)

📋 Change Log since v1.3.0.91

• New protocol [eSky 150 v2](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#ESKY150V2---69)
• FrSky D16 LBT v1.x & 2.1: adjust LBT detection threshold and LBT power to match ETSI requirements
• [Firmware updates manual](https://www.multi-module.org/using-the-module/firmware-updates)

📋 Change Log since v1.3.0.87

• Protocols appearing in alphabetic order, only available in the latest OpenTX 2.3.8 nightlies (not published yet)
• Video in action: https://youtu.be/eiExuVHtWDw
• Only show protocols which are installed in the Multi module
• the only exception is FrSky D8 and V8 which will still appear if disabled but will show up as invalid
• RX protocols have now a disable LNA feature and less unuseful settings
• New protocol [Skyartec](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#Skyartec---68)
• [Firmware updates manual](https://www.multi-module.org/using-the-module/firmware-updates)

📋 Change Log since v1.3.0.81

• Protocol FrSkyX and FrSkyX2: improve TX to RX SPort code
• Protocol [FrSkyL](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#FRSKYL---67): New
• Compatible model: L9R RX
• Protocol: FrSkyL (66)
• Sub protocols: LR12 36ms and LR12_6CH 18ms
• Extended limits supported
• Telemetry: no
• Protocol [FrSky_RX](https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#frsky_rx---55): RX addition of D16v2.1 FCC/LBT
• + 12 more

📋 Change Log since v1.3.0.79

• Protocol PROPEL: New
• Compatible model: PROPEL 74-Z Speeder Bike
• Protocol: PROPEL (66)
• Sub protocol: none
• Autobind protocol
• Extended limits not supported
• Telemetry supported: LQI, life, model status (flying, taking off, landing, landed/crashed,...)
• 14 channels in use due to many features